GrowPulse

LF-ONE 'Little Farm' Assembly Guide

The step-by-step guide to assemble your new LF-ONE

This manual is your guide to preparing and assembling your new LF-ONE unit. Inside you'll find step-by-step instructions to make sure you assemble your unit correctly. The only tools you will need are a Phillips-head screwdriver and wrench, both of which are included in the kit. We've also included several extra screws of each type in case you should happen to drop or misplace one."

Before You Begin

Before you begin actual assembly, it is a good idea to browse this manual to get an idea for the steps involved and to identify and organize the tools you will need. We have included a checklist on page 2 of this guide with the kit's contents.

Questions? We Have Answers.

We recommend you assemble your unit nearby to where you want to place your LF-ONE so that you won't have to move it once assembled.

It is also helpful to place your unit in an area with airflow or at least in an open area. This will aid in plant growth.

Should you have questions on the assembly, we are here to help. We have an assembly video posted on our website at www.growpulse.com under the LF-ONE support section, which will provide a good visual on how the assembly works. You can also call us at 804.997.9398

System Contents

Safety Notes and Tips from GrowPulse on your LF-ONE

ACCESSORIES

Keep indoors at temperatures between 45-90 degrees Fahrenheit.

II. LF-ONE is designed for use indoor use only - Do NOT use outdoors.

III. Unplug unit when not in use.

IV. To avoid electric shock, do NOT touch plugged-in unit while in contact with water line or faucet.

V. Keep children and pets away from nutrients and LF-ONE supplies. Nutrients are not meant to be consumed or ingested. In case of accidental ingestion, seek prompt medical attention!

VI. Keep unit away from open flames, fire, or chemicals.

VII. Make sure unit rests on a flat, stable surface that can support the weight of the unit, water, and contents. Exercise caution when moving the unit.

VIII. Do not attempt to stack LF-ONE units on top of each other.

IX. Follow nutrient mixing instructions closely. Do not overmix nutrients or you could jeopardize crop growth.

X. Thoroughly clean unit after each grow cycle XI. For best results use only GrowPulse LED grow lighting and GrowPulse supplies and nutrients with the LF-ONE system.

Take the longest hole, slide it into the top hole on the inside of A2, and slide it down through A2 and A1 to the bottom hole on the inside of A1 (between F1 and F2).

3 Take the shortest, and last, hose and slide it into the middle hole on the inside of A1 (just above F2). Slide the hose down and out the bottom hole (between F1 and F2).

Drain Pipe

On the left (B Poles) side of the unit, install the smaller set of pipe clamping PC-B-3 – three piece cone clamps. Connect the two sets of screw holes. Use the screws provided N-1. Now connect the System Drain Pipe. To connect the System Drain Pipe, connect by pushing into the three clamps until it snaps into place. Rotate the pipe so that the water collection funnels are in position under the drainage holes of the system.

On the right (A) Pole(s) of the unit, install the larger set of pipe clips (PC-A) three, one piece, on each frame, F2, F3, and F4 – where you will find pre-set screw holes. Use the screws provided [4]. Connect the wire conduit (WC with cables insulated). To connect the conduit, connect the PVC pipe holding the electric cables to the L-FUNE unit by pushing it into the three pipe clamps until it snaps into place. Note that the smaller connector (L-shaped hook piece) goes in at the top (It connects into the opening (A3) in the top (arc step) 6). The longer, upside-down L-shaped connector, paces in the bottom, into the water mixing toy, to provide power for the pump.

Wiring Conduit